Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
How do you really feel about How to Install a Bathtub?
Mounting a tub isn't exactly brain surgery, but it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately tough project. If the old tub is conveniently accessible, the task can move easily; if you need to open up a wall surface to eliminate the old bathtub and also position the new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and set in the new one. See to it you have actually qualified on your own for the task and fit attempting it. As opposed to working with a contractor to take control of a halfway-completed project, it is far better to think about using one before you start. Chances are you may need a specialist plumber to make tube connections.
This write-up will assist you mount a new tub in your bathroom if you have actually currently purchased a new bathtub and also don't need to alter the setup of your previous water system pipelines.
Your devices and material checklist must consist of the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to now prepare to be suited its final placement.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Before going on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wood boards under its feet, position the bathtub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit the bottom of the outermost adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply and inspect all joints and new pipework for leakages and also tighten them if needed. Load the bathtub as well as likewise examine the overflow outlet and also the typical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the tub must wait till the bath tub has been used a minimum of when as this will settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The former type must be linked to the tap ends initially, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bath and also the tiling, leading to complications with wetness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the tub with water prior to securing, to allow for the activity experienced when the tub is in use. The sealant can crack rather very early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very intrigued by How to Install a Bathtub Yourself and I am praying you liked our article. Those who appreciated our page plz do not forget to share it. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .
Ring, relax, resolved! Report this page